DRV8825 Stepper Motor Driver Carrier, High Current

$9.99 Buy It Now or Best Offer
free,30-Day Returns

Seller Store chicago_electronic_distributors
(7490) 100.0%,

Location: Port Charlotte, Florida
Ships to: US,
Item: 253149491024

Restocking Fee:No
Return shipping will be paid by:Buyer
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money Back
Pololu:Pololu
Type:motor driver
MPN:P2133

This breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-temperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling). The driver has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver carriers, so it can be used as a higher-performance drop-in replacement for those boards in many applications. This board ships with 0.1″ male header pins included but not soldered in. Overview This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver’s key features: Simple step and direction control interface Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45 V maximum supply voltage Built-in regulator (no external logic voltage supply needed) Can interface directly with 3.3 V and 5 V systems Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout Short-to-ground and shorted-load protection 4-layer, 2 oz copper PCB for improved heat dissipation Exposed solderable ground pad below the driver IC on the bottom of the PCB Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information) We also carry a DRV8824 stepper motor driver carrier that can serve as a direct substitute for the DRV8825 carrier when using lower-current stepper motors. The DRV8824 can only deliver up to 0.75 A per coil without a heat sink (1.2 A max with proper cooling), but it has larger current-sense resistors that allow for better microstepping performance than the DRV8825 carrier at low currents. The only way to tell our DRV8824 carrier apart from the DRV8825 carrier is by the markings on the driver IC; if you have a mix of the two, you might consider marking them (there is a blank square on the bottom silkscreen you can use for this). Note that we carry several other stepper motor drivers that can be used as alternatives for this module (and drop-in replacements in many applications): The DRV8834 carrier works with motor supply voltages as low as 2.5 V, making it suitable for low-voltage applications. The DRV8880 carrier offers dynamically scalable current limiting and AutoTune, which automatically selects the decay mode each PWM cycle for optimal current regulation performance based on factors like the motor winding resistance and inductance and the motor’s dynamic speed and load. The Black Edition A4988 stepper motor driver carrier is a higher performance version of our original A4988 carrier. This product ships with all surface-mount components—including the DRV8825 driver IC—installed as shown in the product picture. This product ships individually packaged with 0.1″ male header pins included but not soldered in. Some unipolar stepper motors (e.g. those with six or eight leads) can be controlled by this driver as bipolar stepper motors. Unipolar motors with five leads cannot be used with this driver. Included hardware The DRV8825 stepper motor driver carrier ships with one 1×16-pin breakaway 0.1″ male header. The headers can be soldered in for use with solderless breadboards or 0.1″ female connectors. You can also solder your motor leads and other connections directly to the board. (A version of this board with headers already installed is also available.) Caution: Installing the header pins so that the silkscreen side is up and the components are down can limit the range of motion of the trimpot used to set the current limit. If you plan on installing the header pins in this orientation, please set the current limit before soldering in the pins. Using the driver Power connections The driver requires a motor supply voltage of 8.2 – 45 V to be connected across VMOT and GND. This supply should have appropriate decoupling capacitors close to the board, and it should be capable of delivering the expected stepper motor current. Warning: This carrier board uses low-ESR ceramic capacitors, which makes it susceptible to destructive LC voltage spikes, especially when using power leads longer than a few inches. Under the right conditions, these spikes can exceed the 45 V maximum voltage rating for the DRV8825 and permanently damage the board, even when the motor supply voltage is as low as 12 V. One way to protect the driver from such spikes is to put a large (at least 47 µF) electrolytic capacitor across motor power (VMOT) and ground somewhere close to the board. Motor connections Four, six, and eight-wire stepper motors can be driven by the DRV8825 if they are properly connected. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble.) Step (and microstep) size Stepper motors typically have a step size specification (e.g. 1.8° or 200 steps per revolution), which applies to full steps. A microstepping driver such as the DRV8825 allows higher resolutions by allowing intermediate step locations, which are achieved by energizing the coils with intermediate current levels. For instance, driving a motor in quarter-step mode will give the 200-step-per-revolution motor 800 microsteps per revolution by using four different current levels. The resolution (step size) selector inputs (MODE0, MODE1, and MODE2) enable selection from the six step resolutions according to the table below. All three selector inputs have internal 100kΩ pull-down resistors, so leaving these three microstep selection pins disconnected results in full-step mode. For the microstep modes to function correctly, the current limit must be set low enough (see below) so that current limiting gets engaged. Otherwise, the intermediate current levels will not be correctly maintained, and the motor will skip microsteps. MODE0 MODE1 MODE2 Microstep Resolution Low Low Low Full step High Low Low Half step Low High Low 1/4 step High High Low 1/8 step Low Low High 1/16 step High Low High 1/32 step Low High High 1/32 step High High High 1/32 step Control inputs Each pulse to the STEP input corresponds to one microstep of the stepper motor in the direction selected by the DIR pin. These inputs are both pulled low by default through internal 100kΩ pull-down resistors. If you just want rotation in a single direction, you can leave DIR disconnected. The chip has three different inputs for controlling its power states: RESET, SLEEP, and ENBL. For details about these power states, see the datasheet. Please note that the driver pulls the SLEEP pin low through an internal 1MΩ pull-down resistor, and it pulls the RESET and ENBL pins low through internal 100kΩ pull-down resistors. These default RESET and SLEEP states are ones that prevent the driver from operating; both of these pins must be high to enable the driver (they can be connected directly to a logic “highâ€� voltage between 2.2 and 5.25 V, or they can be dynamically controlled via connections to digital outputs of an MCU). The default state of the ENBL pin is to enable the driver, so this pin can be left disconnected. The DRV8825 also features a FAULT output that drives low whenever the H-bridge FETs are disabled as the result of over-current protection or thermal shutdown. The carrier board connects this pin to the SLEEP pin through a 10k resistor that acts as a FAULT pull-up whenever SLEEP is externally held high, so no external pull-up is necessary on the FAULT pin. Note that the carrier includes a 1.5k protection resistor in series with the FAULT pin that makes it is safe to connect this pin directly to a logic voltage supply, as might happen if you use this board in a system designed for the pin-compatible A4988 carrier.  such a system, the 10k resistor between SLEEP and FAULT would then act as a pull-up for SLEEP, making the DRV8825 carrier more of a direct replacement for the A4988 in such systems (the A4988 has an internal pull-up on its SLEEP pin). To keep faults from pulling down the SLEEP pin, any external pull-up resistor you add to the SLEEP pin input should not exceed 4.7k. Current limiting To achieve high step rates, the motor supply is typically much higher than would be permissible without active current limiting. For instance, a typical stepper motor might have a maximum current rating of 1 A with a 5Ω coil resistance, which would indicate a maximum motor supply of 5 V. Using such a motor with 12 V would allow higher step rates, but the current must actively be limited to under 1 A to prevent damage to the motor. The DRV8825 supports such active current limiting, and the trimmer potentiometer on the board can be used to set the current limit. You will typically want to set the driver’s current limit to be at or below the current rating of your stepper motor. One way to set the current limit is to put the driver into full-step mode and to measure the current running through a single motor coil without clocking the STEP input. The measured current will be 0.7 times the current limit (since both coils are always on and limited to approximately 70% of the current limit setting in full-step mode). Another way to set the current limit is to measure the voltage on the pin and to calculate the resulting current limit (the current sense resistors are 0.100). The ref pin voltage is accessible on a via that is circled on the bottom silkscreen of the circuit board. The current limit relates to the reference voltage as follows: Current Limit = VREF x 2 So, for example, if you have a stepper motor rated for 1 A, you can set the current limit to 1 A by setting the reference voltage to 0.5 V. Note: The coil current can be very different from the power supply current, so you should not use the current measured at the power supply to set the current limit. The appropriate place to put your current meter is in series with one of your stepper motor coils. Power dissipation considerations The DRV8825 driver IC has a maximum current rating of 2.5 A per coil, but the current sense resistors further limit the maximum current to 2.2 A, and the actual current you can deliver depends on how well you can keep the IC cool. The carrier’s printed circuit board is designed to draw heat out of the IC, but to supply more than approximately 1.5 A per coil, a heat sink or other cooling method is required. This product can get hot enough to burn you long before the chip overheats. Take care when handling this product and other components connected to it. Please note that measuring the current draw at the power supply will generally not provide an accurate measure of the coil current. Since the input voltage to the driver can be significantly higher than the coil voltage, the measured current on the power supply can be quite a bit lower than the coil current (the driver and coil basically act like a switching step-down power supply). Also, if the supply voltage is very high compared to what the motor needs to achieve the set current, the duty cycle will be very low, which also leads to significant differences between average and RMS currents. Additionally, please note that the coil current is a function of the set current limit, but it does not necessarily equal the current limit setting. The actual current through each coil changes with each microstep. See the DRV8825 datasheet for more information. Key differences between the DRV8825 and A4988 The DRV8825 carrier was designed to be as similar to our A4988 stepper motor driver carriers as possible, and it can be used as a drop in replacement for the A4988 carrier in many applications because it shares the same size, pinout, and general control interface. There are a few differences between the two modules that should be noted, however: The pin used to supply logic voltage to the A4988 is used as the DRV8825’s FAULT output, since the DRV8825 does not require a logic supply (and the A4988 does not have a fault output). Note that it is safe to connect the FAULT pin directly to a logic supply (there is a 1.5k resistor between the IC output and the pin to protect it), so the DRV8825 module can be used in systems designed for the A4988 that route logic power to this pin. The SLEEP pin on the DRV8825 is not pulled up by default like it is on the A4988, but the carrier board does connect it to the FAULT pin through a 10k resistor. Therefore, systems intended for the A4988 that route logic power to the FAULT pin will effectively have a 10k pull-up on the SLEEP pin. (This 10k resistor is not present on the initial (md20a) version of the DRV8825 carrier.) The current limit potentiometer is in a different location. The relationship between the current limit setting and the reference pin voltage is different. The DRV8825 offers 1/32-step microstepping; the A4988 only goes down to 1/16-step. The mode selection pin inputs corresponding to 1/16-step on the A4988 result in 1/32-step microstepping on the DRV8825. For all other microstepping resolutions, the step selection table is the same for both the DRV8825 and the A4988. The timing requirements for minimum pulse durations on the STEP pin are different for the two drivers. With the DRV8825, the high and low STEP pulses must each be at least 1.9 us; they can be as short as 1 us when using the A4988. The DRV8825 has a higher maximum supply voltage than the A4988 (45 V vs 35 V), which means the DRV8825 can be used more safely at higher voltages and is less susceptible to damage from LC voltage spikes. The DRV8825 can deliver more current than the A4988 without any additional cooling (based on our full-step tests: 1.5 A per coil for the DRV8825 vs 1.2 A per coil for the A4988 Black Edition and 1 A per coil for the original A4988 carrier). The DRV8825 uses a different naming convention for the stepper motor outputs, but they are functionally the same as the corresponding pins on the A4988 carrier, so the same connections to both drivers result in the same stepper motor behavior. On both boards, the first part of the label identifies the coil (so you have coils “Aâ€� and “Bâ€� on the DRV8825 and coils “1â€� and “2â€� on the A4988). For those with color-sensitive applications, note that the DRV8825 carrier is purple. Dimensions Size: 0.6″ x 0.8″ Weight: 1.6 g General specifications Minimum operating voltage: 8.2 V Maximum operating voltage: 45 V Continuous current per phase: 1.5 A Maximum current per phase: 2.2 A Minimum logic voltage: 2.5 V Maximum logic voltage: 5.25 V Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32 Reverse voltage protection?: N Bulk packaged: N Header pins soldered: N Notes: 1. Without included optional headers. 2. Without a heat sink or forced air flow. 3. With sufficient additional cooling. 4. This driver works with 2.5 V to 5.25 V logic. It does not take an external logic power supply. 5. Male header pins are included for the board’s 16 holes, but they are not installed. Visit Our eBay Store: Chicago Electronic Distributors

Frequently Asked Questions About DRV8825 Stepper Motor Driver Carrier, High Current in My Website

brokenmirror.com is the best online shopping platform where you can buy DRV8825 Stepper Motor Driver Carrier, High Current from renowned brand(s). brokenmirror.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling DRV8825 Stepper Motor Driver Carrier, High Current on brokenmirror.com?

brokenmirror.com helps you to shop online and delivers Versace to your doorstep. The best-selling Versace on brokenmirror.com are: VERSACE COUTURE Mens Shirt Small Green Pullover Crew Chain Scroll Logo $225 Versace Bright Crystal EDT Spray 3 Oz For Women by Gianni Versace New in Box VERSACE POUR FEMME BY VERSACE 100ML EDP SPRAY (NEW WITH BOX & SEALED) Men’s Versace Neon Green “Save a Horse. Ride a Cowboy” Graphic Shirt Sz Small Versace VE4387 GB1/87 56mm Black Plastic Rectangle Sunglasses Grey Lens VERSUS GIANNI VERSACE T-SHIRT cotton crewneck black luxury Italy Large Versace Light Grey Geometric Unisex Sunglasses VE4361 539687 53 VE4361 539687 53 Versace Men Cologne Collection Sample Spray Vials 1ml / 0.03oz 7Pc Set NWT VERSACE JEANS COUTURE PANTS trousers solid beige cotton Italy us 36 waist 33 VERSACE VE4391 531771 Havana Aviator Men’s 48 mm Sunglasses Versace 0VE2239 100287 Woman Sunglasses Gold Frame, Dark Grey Lenses, 47MM Versace Medusa Gold Color Glass Ornaments Christmas Luxury Home Décor Versace Collection Men’s White Stretch V-Neck Short Sleeve T-Shirt XS S M L XL Versace MOD 3091-B GB1 Black Crystals Eyeglasses Frames 51-15 135 Italy Designer Versace Eyeglasses Frames MOD.3204 5029 Clear Purple Cat Eye Full Rim 53-15-140 Versace VE4369 GB1/81 Polarized Black/Grey Sunglasses 58mm Versace Eyeglasses Frames MOD.3219-Q-A 5148 Brown Tortoise Leather 54-17-140 Versace Pour Homme 1 ml/0.03 oz Eau de Toilette Spray Vial (12 COUNT) $195 Versace Jeans Couture Men’s Cotton White Iconic Logo T-Shirt Top Size M Versace Jeans Couture Logo Band Leggings Women’s 2 Black Elastic Waist Pull On NEW Versace Jeans Couture Womens Metallic Bike Shorts Purple Size 36 US 0 Gianni Versace Tie VTG 90s Geometric Silk Logo Italy Red Blue Designer Luxury VERSACE VE3291 5215 51mm Transparent Brown Square Rectangle Women’s Eyeglasses Versace Men’s Eros Gift Set Fragrances 8011003876976 Versace Medusa Legend Women’s Bordeaux Cat Eye Sunglasses VE4454-54302-55 Italy Versace Bright Crystal Absolu Eau de Parfum 0.17 oz / 5 ml SPLASH VERSACE MAN EAU FRAICHE * Cologne for Men * 3.3 / 3.4 oz * NEW IN BOX & SEALED Versace Dylan PURPLE Pour Femme Eau de Parfum Mini .17 oz. , New! Vèrsace Men White T-Shirt Versace Eyeglasses Frames MOD.3232 5197 Red Gold Round Full Rim 52-20-140 Versace VE 4393 401/1W White Plastic Shield Sunglasses Green and Grey Clip On Gianni Versace Bright Crystal Absolute Eau De Parfum Spray 1.7 Ounce/ 50 ML Versace Eyeglasses VE3320U 5217 54mm Light Havana / Demo Lens Versace Crystal Noir 3.4/3.3 oz Shower Gel Women New No Box Versace VE 4361 Golden Replacement Arm Side Icon Logo With Screws Genuine New V2 by Versace T Shirt, Size XL, Orange Versace Atelier Vanille Rouge for Men Eau de Parfum Spray 3.4 oz Versace Dylan Blue 3 piece mini set VERSACE eyeglass frames w/ case MOD 3151 blue Versace Eyeglasses-0VE1184 Brushed brown 1269 53mm VINTAGE Versace Metal Jeans 2.5 OZ EDT Spray with Bag for Women NEW Old Formula VERSACE Underwear ‘BAROCCO’ Designer Stretch T-Shirt Italy 5 M Gold/Black *NWT* Red Jeans by Versace, 2.5 oz EDT Spray for Women Baby Blue Jeans By Gianni Versace For Men. Eau De Toilette Spray 1.6 Ounces Versace Jeans Couture Black Sneakers Versace Yellow Diamond Intense for Women 3.0 oz Eau de Parfum Spray Brand New Versace Women’s “Jersey Topeka” La Greeca Bikini Panties Versace sz 2 US S IT 40 Level Ten Men’s T-shirt Versace Pattern Strip White Size M Versace L’Homme 3.3. fl oz – 100 ml Eau De Toilette Natural Spray Men Versace Sunglass Gift Storage Empty Box 7″x3″x3″ Versace Pour Homme Oud Noir by Versace for Men 3.4 oz Eau de Parfum Spray Men’s Versace Gift Set, New! New Vintage Versace Green Jeans Eau De Toilette Cologne 75ml 2.5 Oz VERSACE VE2255 10021 Gold Blue Unisex Large 63 mm Sunglasses Versense By Versace 1.7 Oz For Women 90% Full @@@@@@@@@@@@@@@@@@@@@@@@@@@@@ Versace 9”x7”x3″ Empty Black GIFT BOX Jewelry Bag/Wallet Sturdy Gift Wrapping Versace Yellow Diamond Eau De Toilette Spray for Women 1.7 oz / 50 ML New Sealed Versace Sunglasses MOD.4361 5217/73 Tortoise Gold Logo Frames with Brown Lenses Versace Men’s Eros Gift Set Fragrances 8011003885183 Brand New VERSACE JEANS COUTURE Men’s Black Embroidered T-Shirt Size M VERSACE VE3350 108 Havana Demo Lens 55 mm Men’s Eyeglasses Versace Eros Smell Like Men Roll On Body Oil by YZY Perfume12 Ml 3x VERSACE POUR HOMME OUD NOIR EAU DE PARFUM SPRAY FOR MEN 3.4 Oz / 100ml BRAND NEW 5-pc Fragrance Sampler FOR HIM Macy’s NEW Versace Givenchy Missoni Azzaro Wood NEW 19v69 Versace Red Oversized Clamshell Sunglasses Travel Hard Case Men’s Black T-shirt Black Rhinestone Tiger Head Versace Pattern Size M Versace Women’s Havana Geometric Square Sunglasses – VE4431-514887-50 – Italy Versace NEW Opal Beige Womens Cat Eye Frames Medusa 54-18-140 Eyeglasses VE3336U Versace Man Cologne Eau Fraiche EDT for Men by Versace Versace GLAM MEDUSA VE 1275 Black 54/15/140 women Eyewear Frame Versace Man Eau Fraiche 0.3 oz EDT Mini for Men New in Box – Best Price Versace Woman Sunglasses, Black Lenses Acetate Frame, 0VE4281 GB1/13 57mm Versace VE 4436U VE 4437U Golden Replacement Temple Icon Logo Genuine New 1K Versace 2019 Medusa Print Top 36 38 2 Blouse Shirt Gift Bag XS S Versace Man Eau Fraiche by Versace for Men 6.7 oz EDT Spray Brand New Versace Tribute Collection box printed tissue paper Andy Warhol Native American Versace Collection Men’s White Graphic Crewneck T-Shirt Sz XL 2XL NEW Versace Jeans Couture Womens Organzino Print Cutout Dress Size 36 US 0 NWT NWT Men’s Versace Classic Blue Slim Fit T Shirt size Medium From Early 2000’s Versus Versace Eau De Toilette 50ml 1.7 fl oz Womens Perfume Italy Yellow Diamond by Versace for Women 6.7 oz EDT Spray Brand New Versace VE3294 GB1 53mm Eyeglass Frame BLACK w/DEMO LENS Mini Versace Bright Crystal Absolu 0.3 EDP Travel Spray Brand New Women Tester VERSACE Man EAU FRAICHE Cologne Mini 0.17 oz (5ml) EDT Splash for Men NEW IN BOX Versace Bright Crystal Eau de Toilette EDT for Women – Your Choice of Sizes NEW VERSUS by GIANNI VERSACE 3.3 FL oz / 100 ML Eau De Toilette Natural Spray In Box Versace Sunglasses VE2264 100287 Matte Gold Dark Grey Lens Round Authentic Versace Women’s 55mm Transparent Violet Sunglasses VE4441-520968-55 Versace Eros By Versace 0.17oz./5ml Edt Mini Splash For Men New In Box 4 Vials Sample VERSACE CRYSTAL NOIR for Women 0.03 oz 1 ml Eau de Toilette Spray Versace Jeans Couture Women’s Full Print Sweatpants size XL VERSACE Logo Black Jacquard Clutch New VERSACE L’HOMME by Versace Eau De Toilette Spray 3.4 oz Men Sealed VERSACE WOMAN Perfume 3.4 oz / 1.7 oz / 1 oz EDP Spray for WOMEN by Versace Versace Men’s Floral Print Swimwear Swim Board Shorts Versace sz 4 US M IT 50 VERSUS by Gianni Versace After Shave Lotion 3.3oz-100ml Splash New Rare (BO12 2 x Versace pour femme Dylan Blue EDT Spray Vial Sample 1ml / 0.03oz Each Authentic NWT Versace Unisex Men T Shirt Mitchel Fit Large 100% Cotton L Medusa LADIES VERSACE MOD.1163-B 1013 130 52[]16 SLEEK SUNGLASSES/EYEGLASS FRAMES ONLY Blonde by Gianni Versace 3.3 oz / 100 ml Eau De Toilette spray tester for women Mens Pullover Fleece Hoodie